How To Build Your Own Plant Stand

How To Build Your Own Plant Stand – Hello! It’s Mandi from Doing Good in the Midwest. As I learned more about not killing my houseplants, I gained the courage to fill my house with more and more of them (so much so that I ran out of room!). My one-and-a-half-year-old finally learned how to “not touch” the houseplants, which has inspired me to work on the plant stand, with minimal fear. of the ability to clean the soil. on the floor. (I hope we’re past that stage! Please don’t burst my bubble!) I have a very specific little thing in mind and – as always – can’t find anything in the store or online that fits in my budget, so I fell back on my usual plan to just do it myself!

This project was very quick and easy, as far as the furniture goes, since I decided to use the brackets instead of trying the wooden method. Difficulty levels and prices vary depending on whether you want to make your own wooden circle. I will talk a little about the options below. And guess what? I have heard your cries and I am working hard to include more information on the estimated cost of the equipment, so you can make a better decision if this project suitable for you.

How To Build Your Own Plant Stand

4 3/4″ or 1″ square dowels (I used 3/4″ x 36″ long dowels and cut them to 28″.)

Give Your Plant A Throne

1″ x 12″ x 2″ pieces of wood instead of the wood circles listed above. (A piece 2x the size you need is $18 at Lowes.)

Wood: $15 – I used half of an $18 board, left a 1′ x 2′ board for another project, and four 36″ dowels at $2.49 each.

Paint & stain: $3.50 – I used 1/4 of a $5 can of spray primer, 1/4 of a $5 can of paint, and less than two ounces of Minwax stain, which cost $4.77 for 8 oz.

Sandpaper: $2 – I used a sheet of $4 4-pack of 80 grit sandpaper and 1 sheet of a $4 4-pack of 180 grit sandpaper.

Diy Carved Hexagon Planter With Plant Stand • Ugly Duckling House

The following steps will cover the process of cutting your own circle. I decided to cut my own because I had trouble finding a pre-cut circle in the size I wanted that didn’t have beveled edges, and since I already had a jig saw, I knew it would be easy eight to do. You may be able to find wooden circles at craft stores, but they may not be thick enough to hold the length of the screws that come with your brackets. If you use a thin circle of wood, remember that you need to buy short screws to attach the brackets. You also have the option of gluing together two of the same wooden circles to make a thicker, nicer looking shelf of plants. I found this wood on Amazon that doesn’t look too bad, although the edges of the plywood are notorious for chips, so I wanted to fill the wood with filler and sand before painting. Who knows? You may even be able to find two inexpensive round cutting boards that will work well for your cabinet!

Step 1: Trace the outline of the 10″ plate to the wood material. I used poplar, but since you are painting this wood, the type is not very important. Leave the border evenly. around the circle you trace so you can easily fit the jig saw on both sides of the line when cutting.

Step 2: Cut along the lines you traced with the jig saw. Slowly but surely wins the race! If you go too fast, you won’t be able to follow the line exactly, and then you’ll just end up with a nice circle. When I cut, I hold the edge of the board firmly on the table with my left hand while I cut with the jig saw in my right hand. Of course, when I cut, I have to move the board so that I don’t cut on the edge of the table. Step 3: Sand the edges of the wooden circle to make them nice and smooth. While you’re at it, sand down the wood planks just to knock down the factory roughness or corners they may have.

Step 4: First and paint the wooden circle. I lightly sanded in two coats of primer with 180 grit sandpaper to give it a good finish for the two coats of paint I applied next.

Diy Plant Stand

Step 5: Remove the square dowels. When you’re buying dowels at the store (I got mine from a craft store), try to find ones that have a similar grain. Most of them will take the same color. I applied the stain with a paper towel, and after I was done, I allowed the stain to cure completely. Only then did I throw away the paper towel. If you throw it away when the smoke is fresh, you will be at risk of an accident. Do not work with stain when pregnant or old and always wear a mask. If you are particularly concerned about smoke, you may want to look into wood stains.

Step 6: Find the nicest looking edge of your stained dowels, and mark the connecting points on the outside. Measure in 7″ from the bottom of your square dowel (the bottom will have red paint on it if you bought it from a craft store) and 2″ from the top, and mark the small details with pencil. Make sure these lines are very clear, or your legs will be a little wobbly.

Step 7: Place the brackets so that their holes are in the middle with the line you marked in step six, practice the plane of the line, and then insert the screws to connect the brackets . On the bottom shelf, I use long brackets with two screws on each side, and then I use small brackets on the top, because they will be seen more. For the brackets with two holes, I just lined the bottom hole with the line I marked, and then drilled the pilot hole on top of the hole after filling the bottom one with a screw. Make sure your brackets are facing the right way at the top and bottom. Step Eight: Find four parallel points on the edge of your circle and draw them. Do this by measuring the circumference of the circle, dividing by four, and then mark the points of the measurement with a tape measure.

Step 9: Drill the holes for the connection points on the bottom of the white shelves from the middle of the bracket along the lines you marked in step eight and then mark where the bracket’s holes are . These must be practiced correctly and must be as good a place as you can get them! Then screw all the brackets (which are now attached to the legs) to the bottom of the white shelves where you drilled the pilot holes. This is a little different to do when managing all the long legs, but it can be done with just one set of hands and minimal commitment.

Diy Wooden Plant Stand

If you’ve got some more woodworking skills, then I also recommend using larger square dowels and resting them by evenly matching the dado cut into the edges of the wood circle. You can use the small dowel joinery technique in the dado to attach the dowel to the edge of the shelf to eliminate the need for L-brackets. But if you want your woodworking projects to be on the easy side, just forget what I said about the joint.

When I first did this pose, the legs were a little wobbly because I wasn’t quick about putting the nails. So I re-adjusted the screw holes (a few inches aside from the original) and cut the legs while I was at it. The picture below shows how the tree stands now. Perfectly straight, sturdy, and a little shorter at 28″ tall instead of 36″. I love it!

If you want to have one more thing on hand for assembling your plant stand, it can be fun to share the cost of the equipment with a friend and spend a beautiful spring afternoon (when end up here, right?) make two stands, so you won’t have to worry about storing leftovers.

This little Arts & Crafts based Mid Century style project is a great, simple solution to my plant stand needs, but it would also make a great table! You can adjust the height, width, and even the number of legs to suit your needs. You can add another shelf in the middle for other plants. The more the merrier! Easy to read on DIY outdoor tree shelf with 3 levels. Taking advantage of the vertical space by building an outdoor shelf for plants is a good idea if you want to keep all your plants outdoors. He can do it

Easy Wooden Diy Plant Stands You Can Make Today

Build your own sit stand desk, how to build your own bike stand, how to build your own power plant, build your own engine stand, build your own stand, build your own monitor stand, how to build your own, how to build your own deer stand, build your own tv stand, how to build your own aquarium stand, build your own stand up paddle board, build your own plant stand