Build Your Own Workbench Plans

Build Your Own Workbench Plans – Inside: This DIY garage workbench is the perfect mobile, multifunctional build to organize your garage, store items, and complete your projects all in one place.

My garage was bursting at the seams like my pants after Thanksgiving dinner and I feared the avalanche of plastic Christmas figurines and rusty tools would be the death of me. I was thankful for my feline reaction and the tetanus shot was up to date.

Build Your Own Workbench Plans

The workbench is 73 1/2 inches long, 37 1/2 inches wide and 34 inches tall. It glides on 5-inch locking casters that can handle 220 lbs each.

Diy Work Bench

Consider size, budget and function when researching the perfect workbench. Visit 10 Best Garage Workbench Builds to inspire your wish list and see tons of designs. And after you’ve built your garage workbench, check out these 10 must-have garage workbench accessories to maximize its function.

*Make sure you have your safety gear before you start. I recommend safety goggles and protection for this project.

I started with plans from Shanty 2 Chic and then I added a few extras to make it my own. Click on the image below if you want the printable plans.

Humble beginnings…before making this workbench I was using my grandmother’s old card table. When I was working on a project, one leg often came off. Needless to say I was ready to graduate from your grandmother’s card table?

Workbench Diy Workbench Workbench Plans

*Double check your measurements. Your cuts may differ due to small errors in the cuts and being slightly off square from what I have here. Measure once cut twice.

Step 1) Create the top and bottom frames. If you are using a Craig Jig make sure to set your board thickness to 1 1/2 inches. Make two pocket holes in the ends of the cross supports of all frames and attach them to the side supports using the recommended 2 1/2 inch pocket hole screws. Apply wood glue to all joints.

Step 2) Drill three pocket holes in all 2 x 4 legs. Drill a pocket hole at each end and offset one from the center about two inches. The middle pocket hole is offset because the middle shelf brackets (step 5) will be nailed to the middle of the leg.

Attach the 2 x 4s to the 2 x 6s using 2 1/2 inch pocket hole screws to complete the legs.

Diy Workbench Plans

Attach each leg to the outside corner of the bottom frame and the inside corner of the top frame. Drill pilot holes and use 2 1/2 inch wood screws. To attach the legs to the frame it was easy to lay the workbench on its side and use scrap wood to prop it up.

Step 3) Outline the casters for easy screw placement before attaching the four 2 x 6 bottom pieces.

Drill pilot holes and use 2 1/2 inch wood screws to attach the four 2 x 6 pieces to the bottom of each leg.

Drill pilot holes and use 1/4 inch lock washers and 1/4 inch leg screws to attach the casters.

Diy Workbench With Simpson Strong Tie Workbench Kit

Put the brakes on the casters and get some help or pull the Hemi yourself trying to flip the beast right side up.

Step 4) Insert the bottom MDF board and fasten it around the perimeter using 1 1/2 inch 18G brad nails.

You can either take a nap on the bottom shelf or proceed to assemble the middle section.

A half middle shelf is convenient for storing small tools to maximize functionality while still allowing larger items to be stored on the lower shelf.

Easy Diy Workbench On Wheels

Step 5) Drill two pocket holes on the ends of the 23 inch 2 x 4s and the center 25 1/4 inch 2 x 4 for the middle frame. Attach with 2 1/2 inch pocket hole screws and wood glue.

Once the frame is complete, attach the 11-inch 2 x 4 vertical supports using 2 1/2 inch wood screws.

Attach the shelf brackets to the inside of the legs 12 1/2 inches from the top using wood glue and 1 1/2 inch 18G brad nails.

To attach the middle frame set it on the shelf bracket and clamp the vertical support in the middle of the cross support of the top frame. Drill pilot holes in the vertical supports and attach them to the center support of the top frame with 2 1/2 inch wood screws.

Sturdy Diy Workbench Plans [ultimate Ideas]

Measure and cut the MDF for the middle shelves. I used two separate pieces of MDF and punched out the pieces for the vertical support with my Rockwell bladerunner. Attach the MDF shelves using 1 1/2 inch 18G brad nails.

Step 6) Set the top MDF board on the top frame and attach with 1 1/2 inch 18G brad nails.

The trim pieces help the integrity of the MDF, especially at the corners and they improve the look by transforming this beast into a sexy beast.

Step 8) Touch up any spots with wood filler and give it a light sanding. For added protection I applied four coats of spar urethane. Being stored in a garage will subject it to some of the temperature changes of living in Colorado.

Diy Workbench Design Fit For A Junker

Now that my garage space is under control, I don’t have to rely on my quick reflexes and immune systems to improve longevity.

Learn 5 simple tips to help you start and finish every DIY project. As a bonus, you’ll also get weekly DIY tips sent to your inbox.

Any DIY project is hard to start and even more challenging to finish. Learn 5 easy tips to help you start and finish every DIY project when you subscribe to my weekly-ish newsletter. This easy to build workbench is big and sturdy and would be a valuable addition to any shop, so get the free plans. own!

All the projects I have worked on at home have been for the home. It’s all about making the home beautiful, comfortable and tidy. Love this little side table!

Workbench — Modern Builds

Alicia always has pieces she wants me to build (you can check out many of my other free woodworking plans), but this one was for me, and only me!

Eventually I realized that I was building these projects on just two saws that were anything but sturdy and a couple of 2×4’s with a 3×8′ sheet of plywood on top.

It really won’t hold anything with significant weight and it’s throwing my builds slightly off square/level/flat.

So I finally decided it was time to build the ‘base’ of my workshop. I have a small workbench on the other side of the shop, but it’s only 18″ x 48″. It’s not nearly big enough for most of the projects I’m building.

Diy Work Benches

My free workbench plans measure 36″ x 73.5″, and include a half shelf on one side, and are

I thought about making it a mobile workbench and adding wheels, but I’ve decided against it for now, but I know I can add it at any time by cutting off the legs and adding some swivel wheels.

My back thanked me for building this workbench a few months ago. If you’re looking for a great workbench plan that you can build in a day, this is the one!

This post contains affiliate links where we make a small commission on any purchase you make, at no extra cost to you. See our full advertising policy here. Thanks for helping support our blog.

Benchcrafted Roubo Workbench Plan

And there you have it – a sturdy, sturdy surface using our free workbench plans! Only 9 steps to build this…not bad, eh? If you make one for yourself send some shots my way…I’d love to see them!

And check out some of our free DIY plans that you can tackle now that you have the perfect surface to work on!When I started building this mobile workbench, I focused on three main tasks that I wanted to optimize: Spelling , sanding, and assembly. By using the T-Track, I can take advantage of a number of accessories that will keep the project pieces where I want them. Along with the two sliding panels, I stored my sanding and vacuum hose next to my shop vac. With several large drawers and sliding trays, I can store every other accessory and power tool I need to work on this bench!

To keep up with all our latest projects and get a glimpse of what’s to come, be sure to follow us on Instagram , YouTube , and Facebook ! Also, if you want to help fund future projects and tutorials, you can sign up to become a patron!

This project is made of plywood and dimensional lumber from plans I have available. Grab this to do dimensional estimation work and complete your project faster!

Free Workbench Plans And Diy Designs

To start things off, I start by rough cutting the 4×4 I will use for the base. I usually keep rough cut lumber 1″-2″ longer than the final dimensions needed.

This step is optional, but I wanted my boards to be as straight as possible, so I joined and plane all 4 sides. This made my 4×4 about 3-1/4″ square.

I used Domino’s for this

Build your own home plans, build your own gazebo plans, build your own greenhouse plans, build your own workbench plans free, sauna plans build your own, build your own furniture plans, build your own workbench, build your own shed plans, build your own mailbox plans, build your own garage workbench, build your own sofa plans, build your own house plans