Build Your Own Diy Bathroom Vanity Plans

Build Your Own Diy Bathroom Vanity Plans – Freestanding bathroom vanity plans have two large cabinet doors, two drawers and open storage space under the sink. We love the exterior that is easy to clean and maintain. This vanity works with a standard over the counter vanity.

This is one of my favorite bathrooms I’ve ever designed and built. I love it because it’s great for storage, and the simple clean exterior lines are easy to clean and keep clean.

Build Your Own Diy Bathroom Vanity Plans

The hinge is made for fitted doors and is very easy to install. One thing though – you have to use a clasp or hook to keep the door closed with these hinges.

Amazing Diy Bathroom Vanity Plans & Ideas

We love how this vanity turned out! An open shelf in the center stores towels nicely (I envision a large basket for washcloths and hand towels or guest towels), and less attractive bathroom necessities can be hidden behind the door.

Please read the entire plan and all comments before starting this project. It is also worth reviewing the introductory section. Take all necessary precautions to build safely and wisely. Work on a clean surface free of blemishes or dirt. Always use straight boards. Check the square after each step. Always pre-drill holes before attaching with screws. Use with end nails for a strong hold adhesive. Dry glue does not stain, so for messy projects, wipe excess glue off bare wood. Be safe, have fun, and ask for help if you need it. best wishes!

Start by building a basic box for the vanity. We use 3/4″ pocket holes and 1-1/4″ pocket hole screws.

We adjusted the middle shelf, cut it to size. We need to cut the center to make the pipes.

Diy Bathroom Vanity Ideas

We built the front frame separately with 3/4″ pocket holes and 1-1/4″ pocket hole screws. Then we attach the front frame with 1-1/4″ finishing nails and glue.

We built drawers with 1/2″ thick stock using 1/2″ pocket holes and 1″ pocket hole screws. We attached 1/4′ plywood to the bottom with a final nail glue.

Fill all holes with wood filler and dry. Apply additional layers of wood filler as needed. When the wood filler is completely dry, sand the project with 120 grit sandpaper in the direction of the wood grain. Project vacuumed to remove sanding residue. Remove all sand threads from work areas. Wipe the project with a dry cloth.

It is always recommended to do a test coat or patch on a hidden area to ensure color evenness and adhesion. Use primer or wood conditioner as needed This post is part 3: Creating the part where I came up with this crazy idea to build my own 60 inch DIY bathroom from scratch. Be sure to check out the other parts in this tutorial series:

Left Offset Bathroom Vanity

This next part is where things start to get more difficult. This is not necessarily a “how to” from a professional woodworker.

The problem with building this vanity is that I am not working from plans. Unless you know how to create woodworking plans, most beginners look for plans online and follow them.

How to use a McCall or Butter pattern to sew a dress if you’ve never done it before, right?

This article is about how I created partitions to separate the vanity drawers from the rest of the interior.

Bathroom Corner Vanity

I’m not good at using SketchUp, the free 3D drawing software that many woodworkers use to plan and visualize their projects.

I knew my vanity was exactly 60 inches long and over 22 inches deep and about 32 inches long.

A rough drawing allowed me to see it all on paper and figure out how wide an opening I would create for vanity doors and drawers. I can see where I need to create partitions.

Since I’m not a master builder, I wasn’t sure if I could do fitted doors (ie doors that attach to the vanity opening) or if they were inset (ie hang over the vanity opening).

In Bathroom Vanity » Rogue Engineer

To create drawers for both of your own sinks, I need to create partitions so that the drawers are separate from the rest of the room where the faucet is located.

Although I measured the depth of the base, I did not measure the depth of the top to make sure they were the same measurement!

Vanity was not the same measure as the bottom! Which meant I had a big ‘ole gap!

I don’t know if you can see below (see the black arrows), but this front plate was slightly bent.

Building A Diy Bathroom Vanity: Part 5

Imagine you’re working with useless rectangles anyway, but you actually have curved wood! LOL

It’s hard to explain, but I had to push these studs back a bit to close the gap.

There were a few other oddities, which I won’t go into all the nitty gritty (unless you really want to know – we’ll talk about it in the comments section).

But let me share the solution: I happened to have a small 1/2 inch thick piece of red oak.

Homemade Bathroom Vanity/cabinet Plans You Can Diy Easily

Before gluing the part in place first, I positioned it exactly where I wanted it, then traced the position.

I made sure it was at the right angle and not bent. And I also confirmed that it is even with the vanity side.

Correctly, I was on the back of the vanity and nailed it where Brad was nailed.

I’d hate to run into all these little things, but they were well-educated. I’m sure my DIY vanity will be cleaner and better than this!

How To Build A Diy Vanity With Drawers {free Plans And Video!}

While at Home Depot or a home improvement store, lay the wood flat and make sure it is flat and not bowed or warped. You don’t want those pieces for your vanity! Check out my article on 7 Things You Need to Know About Lumber Before Renovating or Building Your Next Project.

When building a DIY bathtub or any other project where you need perfect 90-degree angles, be sure to check this at every step of the project. A missing parameter skips the next step.

Before gluing and lining up, I used my speed square to make sure the splits were as straight 90 degree angles as possible (you’ll see in the next post why this is SOOOO important, especially when trying to insert drawers correctly).

I recently went to a woodworking show and bought some of Woodpecker’s Box Clamps, which clamp your wood joints at 90-degree angles to make sure you’re getting the right angles. I wish I had these when I was building the main pieces of the DIY vanity! I may have avoided some of the issues I ran into.

First Vanity Build

Thanks, I didn’t have to prepare another partition for vanity. But if I had, it would have been nice to have more plywood on hand.

But it was helpful to buy extra red oak boards in different sizes so that I would have one available when I needed to wrap a piece. Make sure you have extra wood if you have to get creative and piece-meal things together! 🙂

I know the undermount washers we are installing require the parts to be cut down a bit. But since I had no idea how low to cut them, I went ahead and installed the partitions at the same height as the vanity.

If I knew how deep the bathtubs were going to be, it would have been much easier to cut the pieces to the correct height.

Small Size, Big Style Diy Bathroom Vanity

In this part 4 of the DIY Bathroom Vanity series you will see how I created the vanity drawers and the issues that came up during the step and how I worked around them! 🙂

Thrift Diving inspires women to decorate, improve and maintain their own homes…using paint, power tools and thrift stores! Use these 5 printables, checklists, and ebooks to get you started! This post is part 4 of the Making Drawersin series where I came up with this crazy idea to build my own 60 inch DIY bathroom from scratch. Be sure to check out the other parts in this tutorial series:

I stopped at my last post where I told you how I installed partitions in a DIY vanity. Now that the partitions were in place, I had something to attach the drawer slides to and create the drawers from scratch.

First, I know I have an issue with my vanity being “square” and hunky. This is a

Rustic Bathroom Vanity

And the side-mounted drawer slides you get from Home Depot require such precision and can be too thin if you don’t have your measurements.”

But I thought I’d do my best and roll with the punches! After all, this nonsense was an attempt to answer the question:

I had never done drawers before, but it didn’t seem too hard. But the challenging part for me

Build your own bathroom, diy bathroom vanity plans, build my own bathroom vanity, build your own plans, build bathroom vanity plans, build your own vanity, diy build bathroom vanity, how to build your own bathroom vanity, build your own bathroom vanity plans, build your own bathroom vanity, build your own bathroom vanity online, build your own bathroom vanity kits