Build Your Own Work Table

Build Your Own Work Table – I’ve wanted a mobile workbench for years. In my old shop, I built small, stationary workbenches from some random scrap wood I had lying around.

But, I quickly found that mobile is always better than stationary, and I really needed a large assembly space to assemble large furniture pieces without crawling on the floor.

Build Your Own Work Table

So I vowed (promise sounds like a strong word…but I’ll use it anyway) that when we sold our old house and I had a new shop, I would start with a mobile workbench big enough to actually work on. above.

The Finished Studio Work Table!

And while I’m thinking about function, it would be nice if it was the right height to serve as an outfeed table for my table saw and have some storage for my most used materials.

That means it should be the ultimate workbench. It was a big role to fill, but I think this is it

So, I’m excited to share with you free plans for this 3-in-1 Mobile Storage Workbench/Outfeed/Assembly Table! You can find the video right here and the step-by-step tutorial below.

I used whole sheets of plywood for this, so it’s pretty big, but I promise it’s very easy to modify your size by changing some of my measurements in the project. If it’s too small for you, feel free to change the frame and plywood sheet size in the plans below.

Incredibly Cool Workbench Ideas (with Pictures And Instructions)

I made it 34 ½″ high because that is the height of my table saw surface. So this height works perfectly for an outfeed table.

If your table saw isn’t 34 ½″ tall like mine, or if you don’t care to use it as an outfeed table and want to make it taller or shorter, set the height of your legs in the plans and it’s easy to modify. 🙂

First, I decided what size to make my workbench. I used whole plywood sheets for mine, so I made two frames the size of my sheets – 4ft x 8ft.

I assembled this frame from 2×4 boards using 1 ½″ pocket holes and 2 ½″ pocket hole screws.

Building A Standing Desk

I made two identical frames as shown above – one used for the top and one for the bottom of the mobile workbench.

After the frames were assembled, I screwed one of my plywood sheets onto the frame using 1 ¼″ wood screws.

Obviously, if you’re making it smaller than a full sheet, you’ll need to trim your plywood sheet to the size you want.

For tips on cutting plywood sheets, check out this guide to cutting plywood sheets easily and accurately using a circular saw!

Vevor Adjustable Workbench Steel Work Table 18

Cut the four corner posts/legs from the 4x4s. If you don’t want to use 4x4s, you can glue and screw 2x4s together to make your own 4×4 posts.

NOTE: 4×4 posts are 3 ½″ x 3 ½″. If you screw 2x4s together to make your own, this will give you 3″ x 3 ½″. However, in this scheme, the slight difference doesn’t matter.

As mentioned earlier, I built this DIY mobile workbench to 34 ½″ tall once completed. So I cut these legs 26 ¼″ long. However if you want your workbench to be taller or shorter, modify this measurement as needed.

I used two 3″ long wood screws to attach these posts to the underside of the 2×4 frame at each corner.

Workbench Plans That Are Cheap And Easy To Build

Remember the second frame I made from step 1? At this point, I attached it to the corner posts using 2 ½″ wood screws.

I have several questions about what I used for my workbench top. For the rest of this project, I used cheap pine plywood. However, for the top, I splurged for a good quality hardwood birch plywood.

I used good plywood to make sure I had a smooth, durable surface to work on.

Similar to step 2, I attached the full sheet on top of this frame. If you modified the sheet size in step 2, do the same here – trim to size.

Working From Home: 8 Vastu Tips To Set Up A Home Office

I attached this sheet to the top frame using 2″ wood screws from the bottom of the top frame.

Now, let’s talk a little about the Kreg clamp tracks I added to my workbench surface. They come in different size kits depending on what size you make your bench. I used a 27″ x 69″ kit.

If you are adding these as well, you will need to follow the instructions from step 5 to trim your top panel to fit your tracks.

I built my frames for this project out of 2x4s before my tracks arrived and I don’t have the instructions. After they arrived, I realized they were designed to be installed on ¾″ thick surfaces. But I was using 2x material so it was 1 ½″ thick. Alas.

How To Build A Diy Mobile Workbench 3 In1 Storage, Outfeed, Assembly

I followed the instructions for drilling the holes for the bolts through the mounting surface. I drilled all the way through my 2x4s. (You can see this in my video above.)

Then I used a large drill bit (large enough to fit the head of the bolt), marked it down with painters tape from the ¾″ end, then drilled ¾″ deep holes in the bottom.

Now, my bolts fit into the hole ¾″ and it was basically the same as mounting to ¾″ material. It’s a little extra work, but not too bad.

Now, this workbench is large and can have a tendency to collapse in the middle. You can add some supports in the middle to help prevent that, but I like to open this space up.

Flexispot Standing Desk Frame Height Adjustable Desk Frame Electric Sit Stand Desk Base Home Office Stand Up Desk (42×24 Black)

So, instead, I attached some 2x4s to the end to provide a little extra support and prevent excessive sagging. I simply cut a 2×4 frame to fit around the top edge of the workbench and screwed it in place using 2 ½″ wood screws.

To add some extra storage and organization to the workbench, I installed some panels and a shelf at the end. I built this section using ¾″ plywood.

First, I installed the plywood panel as shown here with ¾″ pocket holes and 1 ¼″ pocket hole screws cut 13″ from the inside edge of the legs at one end.

Then, I added the side panels on each side flush to the inside of the legs using ¾″ pocket holes and 1 ¼″ pocket hole screws.

Clarke Cwts1 Work Table Supports Pair For Sale Online

Lastly, I used ¾″ pocket holes and 1 ¼″ pocket hole screws to install the stationary shelf between these two panels. NOTE: Double check your own shelf length and cut accordingly. If you are not using 4×4 posts, your length may vary slightly.

And you have one of the most helpful pieces you’ll build for your shop – a DIY mobile workbench!

It’s already my most used piece in the store. I love the cubbies on the end for all my jigs and a large area for my vacuum and a bucket to toss in small scraps while I’m working.

So if you’re ready to work on the ultimate DIY mobile workbench instead of on the shop floor, go build something for printable projects.

The Best Wood To Use For Wood Shelves

And if you like this project, I’d love it if you pin it for later, and don’t forget to subscribe to my newsletter below so you don’t miss out on more awesome projects to come! Each editorial product is independently selected, although we may be compensated or receive an affiliate commission if you purchase something through our links. Ratings and prices are accurate and items are in stock at time of publication.

Introduction This workbench is simple enough and cheap enough that you can build it in a morning, and it’s big enough for serious woodworking and hobby projects. Add a pegboard, bench vise and a few other accessories and you have a serious work station.

This sturdy 30-in. x 6-foot long DIY workbench is the ultimate in simplicity. It’s made from just fifteen 8-foot long 2x4s and one sheet of 1/2-inch plywood and makes for a better tool workbench than most you can buy.

Learn how to build this workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided on the cutting chart. You can screw the framing in with 3-inch screws or hand- or power-nail it with 3-inch nails. Screw the plywood with 1-5/8-inch screws.

Diy Work Bench

To make these project plans even easier to follow, we’ve color coded the parts included in each step. Continue reading to learn how to build this awesome small work table with storage.

We no longer support IE (Internet Explorer) as we strive to provide site experiences for browsers that support new web standards and security practices. You can never have enough store space and you can never have enough tables in that store. While the former is static, the latter can actually be created

Build your own work bench, build your own dining room table, build your own table, build your own sofa table, build your own work shed, build your own work truck, build your own work desk, how to build your own pool table, build your own plasma table, build your own dining table, build your own cnc plasma table, build your own craft table